![]() I’m just not sure why it’s not authenticating when the username and password are correct. As for the second phone, I get a Request timeout (408) message. The first I was able to register just fine, using the domain name and port in Zoiper configuration: :5060. (I’m building this new one to replace it.) But I would think that I should still be able to set this up manually. Hello: I have configured two SIP accounts to be used from Zoiper in android phones. 1 Hi, I have a 3cx instance running on a Intel NUC at a customer, that faces random outages of the SIP-Trunk. I don’t have endpoint manager installed, because the license is in use on my existing system. I have the username set to the extension and the password set to the secret in freepbx. Extension not registering (Error 408 Timeout) FreePBX Networking tlekga (Tlekga) July 24, 2021, 8:51pm 1 Hello, Kindly point me in the right direction. NOTICE res_pjsip/pjsip_distributor.c: Request ‘REGISTER’ from ‘“Systems” sip: ’ failed for ‘192.168.200.89:5060’ (callid: a0020d65a52a9422) - Failed to authenticate NOTICE res_pjsip/pjsip_distributor.c: Request ‘REGISTER’ from ‘“Systems” sip: ’ failed for ‘192.168.200.89:5060’ (callid: a0020d65a52a9422) - No matching endpoint found When I changed the port from 5061 to 5060 it attempted to register the phone but is giving a 401 error. After setting of the Zoiper softphone I try to get it to communicate with Asterisk, but I get a 408 request timeout.Yes I googled that. I'm doing all of this without access to an internet connection so that's why I hardcode the IP address.ħ. ![]() In Zoiper I hardcode the Domain: :5080 and also enter the username and password.Ħ. I install and setup the Zoiper Softphone as indicated in the tutorial. I start asterisk with "asterisk" and "asterisk -rvvvvvv"Ĥ. It works fine on my old laptop using Windows 7 & an older version of Zoiper. I've modified sip.conf and nf to have entries that tie together phones 101 and 102ģ. Just downloaded Voiper 3 & registered 'MyNetfone' on their system seems to dial ok but comes up with 'SIP 408 - Request Timeout' also no incoming audio. I Integrate Kamailio and Asterisk based off of the asipto kb: 4.0.x-asterisk-11.3.0-astdb with both of them running on the same VM.ģ. I'm running Ubuntu 14.04 and Oracle Virtual BoxĢ. I have a virtual environment setup and am trying to get the integration of Kamailio and Asterisk to a least be able to make a phone call based off the Asterisk Hello World example. I don't have a DNS and am not connected to the internet so I'm wondering if I needed to do something different when I installed Kamailio and it asked for a domain name and I gave it. Any ideas?Ġ(3977) DEBUG: : db_do_init2(): connection 0x7fdb6575c4b0 not found in poolĠ(3977) DEBUG: db_mysql : db_mysql_new_connection(): opening connection: ERROR: db_mysql : db_mysql_new_connection(): driver error: Access denied for user (using password: YES)Ġ(3977) ERROR: : db_do_init2(): could not add connection to the pool 0(3977) ERROR: usrloc : register_udomain(): failed to open database connectionĠ(3977) ERROR: registrar : domain_fixup(): failed to register domain I turned on debug and this is what I see and what I'm trying to track down. Subject: Re: Asterisk Integration w Kamailio and Zoiper phone problems Messages sorted by: Ĭheck you databases and mySQL, check odbc show under asterisk CLI. ![]() Last Modified: 13:02:23 If you are experiencing issues with the initial Zoiper installation, this might be due to your antivirus software or file corruption.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |